A.How to make Yuna's Hair Braid(red one in back. Final Fantasy
X-2)
- -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
-What you will need enough red material to reach down to your knees(make it so you can cut it 3 times and have each
strip 2.5-3 inches wide)
-8inches high and 4 inches wide pink material
-white paint
-thread
-light blue yarn(do not need a lot of this)
-stuffing(ecspecially if you are going to a very picky con)
-brown yarn
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -- - - -
- cut the red fabic into 3 pieces(width 2.5-3 inches wide and the lenght from your shoulders to knees for each thing)
- then on the fold each piece on a side then sew the side and a bottom
- then turn each piece inside out
- then stuff each one
- then sew the top
- then sew all three pieces toghether on top
- braid all 3 pieces
- sew the pieces toghether on bottom
- then put the red braid thing to the side and get out the pink material. make it so the longest side is horizontel, then
fold the hamburger way or top to bottom.
- once agian sew it on the side and on the top
- then pull it inside out and sew the bottom
- then paint 2/3 of the pink thing white, let this dry
- then sew this to the end of the red thing, only about .5-1 inches onto the red thing(all the way around)
- then get the brown yarn out and make it so it is 2 inches thick and 4 inches tall
- sew the brown yarn as a group into the pink/ white thing
- then tie(like tieing a shoe,but only once) the blue yarn around the pink/white thing. in the white spot
- the sew it on, like in certian spots make nots on it
- then connect it to your costume and you have it done
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
B. How you make the Psychc'er Gloves(Final Fantasy X-2)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
What YOU will Need
-Gloves(like for the ones in weddings)
-either purple paint or purple dye
-thread
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
- Cut the gloves about 4 inches above your hand or 2 inches acove your wrist
- then fold the end of the glove a little bit down then sew it onto the place where it is touching
- then either dye or paint these purple(do this two times for both, unless package says other wise)
----------------------------------------------------
C. Yuna's Skirt(Gunner)
----------------------------------------------------
What you need
- about 2 1/2 to 3 yards of blue fabric
- about 3/4 to 1 yards of white ribbon with the decoration on the bottom(2 inches wide
includin the dec)
- a little white bottle of paint or white gradient
----------------------------------------------------
- first you cut a long strip of fabric about 4-6 inches wide, it goes around you self and
on each end there is a 5-6 inches left(for tying) and thenfold it hot dog way, sew 3 out of the four sides flip it inside
out and DO NOT SEW THE 4TH SIDE.
- make a 3 rectangle(before cutting fold the pice and make sure it looks right, if to small add
some) so the shorter sides cover almost you whole right side; then do the same method as for the belt part
except after you flip it sew the last side.
- take you white paine or gradient and do that to you 3 rectangles/squares. if your using white
paint then get a bowl of water and a extra bowl; put a little of the white paint in the bowl and your using your fingers.
dip your 3 main fingers into the water and wipe the traingle then quickly dip you fingers into the paint dish and rub it onto
the restangle(when doing this go from the bottom to about were 1/6 is not full of paint. then dip your palm into the water
and rub the origanal white paint till it looks like you want it to, you might have to do this 3-5 times. do this to each rectangle/square.
- now at sew the 1rst and second piece togher. sew the 2nd one 3 inches or so above the 1st one(check
the example, at the end). do the same thing for the 2nd and 3rd.
- put the top of the first into the part of the belt that has not been sew down. now sew this
side down.
- sew thee ribbon stuff a 1/2 inche befor the start of the second and third one and the bottom
of the third one.
TIP: WHEN USING THE GRADIENT TEST IT BEFORE USING IT ON THE RECTANGLES!!
